Friday, January 25, 2019

Birthday and a card Just Because


I needed to make a birthday card for my grandmother and I knew I wanted to use the collage paper, so I decided to work on two cards mainly because I couldn’t decide on which part of the collage paper I wanted to use. 


I started by dabbing ink and water onto the piece of heavier card stock. Using the heat tool to dry the paper before adding more ink. 


I added the Tim Holtz Idea-ology Floral collage paper to my card layer using a matte gel medium. 

Once the collage paper was dry I added some clear rock candy Distress crackle paint to the flower parts and some white crackle paint randomly to the edges. I let that dry over night. 

On a scrap of paper I stamped and cut out a frame from the Tim Holtz Label Frames stamp set. 


Next I got out the sewing machine and stitched randomly around the card layer, I got out a few coordinating pieces of ephemera and arranged then how I wanted them displayed and attached them to the card layer with the sewing machine as well. 


When I was happy with how everything looked, I glued the layer onto a card base. 



  


 




Please follow me on Instagram here! To see behind the scenes photos and more!



Leave me a comment below and let me know what you think! Give me a thumbs up and make sure to subscribe to my YouTube channel!!

Xo- Megan











Thursday, January 24, 2019

I made a book!

I have made a few smaller notebooks and journal type books, but never a hardcover book. So why not try now!

I started by cutting a bunch of sheets sheets of plain white paper in half (20 to be exact). Then I folded those pages in half to create my pages. I grouped the folded paper into 4’s, so that gave me 10 signatures. I stacked the signatures and used binder clips to keep them all together. I measured and drew lines starting in the middle and then one inch out from the center, then two inches from the center. 


Those lines then became my guides for piercing the paper so I could see all the signatures together. 


I used a kettle stitch to sew the signatures together to form my text block. 


I put my text block into a home made book press and applied PVA glue to the spine of the text block. Making sure to cover the binding thread completely. 


While the text block was drying I started on the cover. 
I cut out three pieces of thick card board. The two cover pieces that were as wide as the text block and as tall as the text block plus 1/4 of an inch. And one piece for the spine that was as wide of the spine of the text block. I also drew a line at about a third of the width of the cover. 


I cut two piece of decorative paper the size of the cover plus 1 1/4 inch. I lined the decorative paper up to the line I made and glued it down using the same PVA glue. 


I cut wedges from each corner and left about 1/16 an inch from the actual board so my paper covers the corners nicely. 


I applied glue to the flaps of paper and folded them over the board. 

O

Next I took a piece of book cloth and glued the spine down and then glued each cover down, leaving 1/4 inch between the spine and the covers. I cut small wedges into the book cloth before folding them over the covers as well. 


I took another sheet of decorative paper that was the same size as a page from the text block. I then glued it to 1/4” on the spine of the text block, and glued on side to the cover of the book. I repeated that for the back cover as well. 


I then placed the entire completed book into the book press while the glue dried, to help everything dry flat. 


After about a few hours I removed the book! 
I have to say I am very pleased with how this book looks! 







Thanks for checking it out with me! 

Make sure you leave me a comment and let me know what you think. 

For other inspiration make sure to check out my YouTube channel!










Friday, December 7, 2018

Simple Golden Christmas Card

I wanted to make some Christmas cards for a few special people. I wanted the card to be simple but not necessarily look it. So I started thinking about a way to go about making a card like that, and here’s what I came up with... a beautiful, gold embossed Christmas card!


To get this look I used my Christmas greenery stamp from the Tim Holtz Stamptember set. I stamped the image directly on my card base in VersaMark ink in the upper right corner of the card as well as the bottom left corner of the card. 


After stamping in both spots I poured gold embossing powder on the entire image, removed the excess and used my heat tool to set the embossing powder. 


I then created my sentiment. Using the same Stamptember set. I cut a small rectangle out stamped in VersaMark ink again. Used the same gold embossing powder, removed excess and again used my heat tool to set the powder. I then cut a smaller rectangle out of fun foam and taped it to the back of my sentiment. 

I put a few lines of tape on the back of my foam lined sentiment. I then cut a piece of gold thread and created loops that peak out from the back of the sentiment. 


And finally attached it to my card base. 



Please follow me on Instagram here! To see behind the scenes photos and more!

Leave me a comment below and let me know what you think! Give me a thumbs up and make sure to subscribe to my YouTube channel!!

Xo- Megan







Saturday, October 13, 2018

Halloween Distress Cards No. 4,5 & 6

I have three little ghoulish nephews I wanted to send a special Halloween wish to. So I thought what better than the Tim Holtz sizzix Ghoulish dies....


I started on the background... by using the blotting technique with Black Soot Distress Oxide and a squirt or two of water on a piece of watercolor paper. 


Next I added a small amount of Wild Honey Distress Oxide ink, using the same blotting technique. 



I cut out each of the “ghouls” from the Goulish die set. 
I blotted the skeleton in Iced Spruce Distress Oxide, the vampire is blotted in Seedless Preserves Distress Oxide and the zombie is blotted in Twisted Citron Distress Oxide. 



I cut out “trick or treat” from the Halloween words thinlit set. 
I blotted it in Spiced Marmalade Distress Oxide. 


I blotted a strip of watercolor paper in Black Soot Distress Ink. Using the Ghoulish die set, I cut out several sets of bats. 

With the Martha Stewart circle cutter I cut out circles in velum. 


Before gluing all my elements together, I wrapped some bronze thread around the bottom of my card layer. 


I added a small piece of black paper behind the “trick or treat” and glued everything to the layer. 



Using the stamping platform I was able to stamp the sentiment (from the Monsterous stamp set) inside all three cards with ease!


I added some spiderwebs from the Tangled Webs stamp set using London Fog Memento ink. 









I absolutely love how these cards turned out! A little bit spooky and a little bit fun... I know my nephews love them!



Please follow me on Instagram here! To see behind the scenes photos and more!

Leave me a comment below and let me know what you think! Give me a thumbs up and make sure to subscribe to my YouTube channel!!

Xo- Megan